When it comes to the classification of
underwear, it is really diverse. According to the function, there are sports underwear, nursing underwear, etc. According to the cup, there are 3/4 cup
bras, 1/2 cup bras, etc., but you know how to classify them according to the production process. ? The following editor will give you the popularization of the production process of underwear. In fact, in addition to the above classification, our common underwear, according to the production process, can also be divided into mold cup underwear, quilted underwear (clamping bowl), and single-layer underwear. 1. Mold cup underwear. Mould cup underwear refers to the underwear that the cup part is made of sponge, sprayed cotton or silk cotton under high pressure and high temperature to make the underwear of women's breasts. From the side section of the cup cover, there are usually traditional type and now popular three-dimensional cup cover. The traditional type has a uniform thickness, while the three-dimensional cup cover is thin on the top and thick on the bottom. Therefore, the three-dimensional circumference has a certain correction and concentration effect. Most of the bare cup products on the market today are mold cup underwear. Mould cup underwear has a variety of thicknesses to choose from, which can be roughly divided into thin cups, ordinary cups, three-dimensional cups and super three-dimensional cups. Because the cups are shaped by heat pressing, the design of the mold cup underwear is mainly reflected in the process of molding and the selection of various sponge cup shapes. In terms of shape, some cups are pointed and some are round, and cups with natural shape and suitable capacity should be selected. Mould cup underwear is usually covered with a layer of the same heat-pressed fabric on the outside of the cup (without breaking it into two or three pieces) to make the chest more plump and shapely, with a smooth surface, suitable for wearing tights or thin clothes, especially White shirts in summer, tight T-shirts and the like... In addition to the choice of cups, the use of various parts of lace has become the focus of the design of mold cup underwear. The side and bottom of the cup cover; or the cup cover is smooth and clean, and lace is used at the heart and under the support to form a contrast between complexity and simplicity. The design of the mold cup underwear, due to the shape of the cup, the design of the heart position is very important. The heart position is divided into width and height. Usually, the cup cover area is large and the heart position is higher; the cup cover area is small and the heart position is short. The narrower the heart position, the better the purpose of restraining and concentrating the chest, but when it is too narrow, the underwear will not fit the body, and the phenomenon of emptiness and looseness will appear. The width of the heart is usually 1 to 2 cm, and its height usually does not exceed the bust line. In addition, the size and hardness of the steel ring are also very important. Mould cup underwear usually has a steel ring attached to the bottom to support the sagging breasts and squeeze the flat breasts to the middle. The size of the steel ring should be appropriate. If the width is too small, it will not only wear tight, but also the underwear will move up; if the size is too large, the effect of the steel ring will be lost. Second, quilted underwear. The cup cover of the quilted underwear is made of fluffy cotton hot-pressed to a certain thickness (usually a thin layer), glued and pressed between two layers of knitted fabrics, and made by changing the cutting of the cup cover and fixing the lower edge steel ring. It is also commonly referred to as 'clamping bowl'. The quilted underwear feels soft and comfortable, and can be used to correct and beautify the human body by shaping various shapes by different cutting of the cup. The quilted surround is divided into two-piece and three-piece, or even four-piece in cutting. The finer the points, the better the three-dimensional shape of the chest. 'Two-piece' underwear is to open horizontally, diagonally or vertically on the cups to form upper, lower or left and right two pieces, which is suitable for young women with standard breast shape. 'Three-piece' underwear is to break the lower circumference into two pieces, the upper circumference is flat and sharp, the lower circumference is round and plump, the shape is three-dimensional and beautiful, and it is suitable for mature and plump women. 'Four-piece' underwear is usually used in all-inclusive four-piece underwear, and an additional piece is added on the upper side to fully cover the chest, which is more stable and firm, suitable for plump women and lactating women; or add a piece under the side to strengthen the underwear The effect of squeezing inward. Reshaping and correcting the human body in the design of underwear can use the cutting of the cup to create a three-dimensional and full shape by using the changes in the chest. In addition to conforming to the human body, the design should use the diagonal-pulled fabric and the chest point of the cup to move to the middle and upward, which affects the breasts to be raised and concentrated. Underwear, on the other hand, can push and elevate the bust in the middle with padded and thickened designs that either attach to the cups or have padded inserts that can be removed at will. In the design of quilted underwear, the steel ring is also used for this purpose. It can support the sagging or flat chest and make it move up and toward the middle. Three, single layer underwear. Single-layer underwear refers to underwear without cotton lining, and the cup part is made of single-layer fabric. Generally, elastic fabrics and lace are used to shape the curve structure through cutting and the properties of the fabric itself, so the cutting is more particular, and the degree of fit is higher. Single layer underwear is suitable for women with fuller breasts. The cutting of single-layer underwear is more particular, and the chest shape should be shaped by the tension of the fabric in the warp and weft directions. In cutting, it is usually divided into one-piece, two-piece, and three-piece. The design of one-piece single-layer underwear mainly uses the elasticity of the single-layer lace, and the lower layer of the lace does not need setting yarn.By taking one or two darts, rely on the natural bulge of the chest to form the shape. Two-piece type and three-piece type are to break the cup into pieces, and the setting yarn is attached under the fabric, which is better than the solidity. The design of single-layer underwear is more particular about the use of lace. The color and position of the lace are more decorative and sexy as a single-layered lingerie due to its revealing skin. Because of its sexy characteristics, single-layer underwear is generally designed with two breasts on the back, and the inside of the cup is also a thin layer. The three production processes of underwear have been introduced to you. As for which underwear to choose, it is recommended to make a choice according to your actual situation.
Shantou Ladymate Apparel Co., Ltd. have now make a decision to enlarge our company in other countries.
We believe our ability can raise a giant wave of innovation among the field of custom bras.
Our company specializes in selling lingerie suppliers as well as providing relevant services.
custom sportswear has obtained many affirmation in the market. Undoubtedlly, our customers are totally satisfied with our products.
Our company is professional in manufacturing shapewear suppliers especially cotton thong underwear.
